Home / All / Steel Wires / Alloy Steel Spring Wires /

ASTM A231 Chromium-Vanadium Alloy Steel Spring Wire

ASTM A231 Chromium-Vanadium Alloy Steel Spring Wire

ASTM A231 Chromium-Vanadium Alloy Steel Spring Wire
CategoriesAlloy Steel Spring Wires
Brandfushun
ModelASTM A231
delivery conditionOil Hardened and Tempered
surface conditionblack, polished
Update TimeMar 29,2024
Detail Information

ASTM A231 Chromium-Vanadium Alloy Steel Spring Wire

Chemical composition

C

Si

Mn

P

S

Cr

V

0.48 - 0.53

0.15 - 0.35

0.70 - 0.90

max   0.025

max   0.025

0.80-1.10

0.15 MIN

Supplying Size:

Diameter:0.3-20mm

 

Our Advantage

1. Stable linearity, good formability. Uniform and beautiful surface condition.

2. High plasticity and good fatigue resistance. And we provide Self-Inspection Reports and    Raw-Material Test Certificates.

3. Professional anti-rust protective packaging. On time delivery, competitive price.

4. Large stock available, no MOQ requirement.

Dimensional tolerances

Wire in coils

The tolerances level for the wire diameter is based on EN 10218-2:1996 level:

-T5 for wire diameter up to and including 0,80 mm;

-T4 for 0,80 mm up to 10,00 mm;

-T3 above 10,00 mm.

Wire in cut lengths

The requirements for length tolerances and straightness are as in EN 10218-2:1996. The tolerance on the nominal length shall only be in plus keeping the same tolerance range

 

A231 Alloy Spring Steel Wire Surface finish

The wire shall be protected against corrosion and mechanical damage. Unless otherwise specified the wire shall be delivered in slightly oiled condition.

 

A231 Alloy Spring Steel Wire Surface quality

The surface of the wire shall be smooth and permissible depth of surface defects at the coil ends shall be in accordance with Table.

By in-line control of surface defects the areas of the coil with defects above the level of Table 7 shall be marked. In-line testing is not performed for FD-grades.

The number of defective parts that can be tolerated may be agreed between the parties.

 

Tensile Requirements

SI Units

Diameter,mm

MPa, min

MPa, max

Reduction of Area, min, %

0.50

2060

2260

/

0.55

2050

2240

/

0.60

2030

2220

/

0.65

2010

2200

/

0.70

2000

2160

/

0.80

1980

2140

/

0.90

1960

2120

/

1.00

1940

2100

/

1.10

1920

2080

/

1.20

1900

2060

/

1.40

1860

2020

/

1.60

1820

1980

/

1.80

1800

1960

/

2.00

1780

1930

/

2.20

1750

1900

/

2.50

1720

1860

45

2.80

1680

1830

45

3.00

1660

1800

45

3.50

1620

1760

45

4.00

1580

1720

40

4.50

1560

1680

40

5.00

1520

1640

40

5.50

1480

1620

40

6.00

1460

1600

40

6.50

1440

1580

40

7.00

1420

1560

40

8.00

1400

1540

40

9.00

1380

1520

40

10.00

1360

1500

40

11.00

1340

1480

40

12.00

1320

1460

40

 

A231 Surface decarburization

The wire grades according to this standard shall be free from total decarburization. The maximum depths of the partially decarburized zone shall be checked at the end of the coils.

 

A231 Testing and inspection

Coiling test

Torsion test

heat analysis;

result of the tensile test

result of the torsion test

actual wire diameter

Tensile test

Alloy Spring Steel Wire that is heat treated in line in the following way: it is first transformed into austenite, quenched in oil or similar quenching medium, followed immediately by tempering by heating to the appropriate temperature.

 

Alloy Spring Steel Wire made from unalloyed or alloyed steels. They are primarily subject to torsional stresses such as in compression and extension springs and in special cases also for applications where the spring wire is subject to bending stresses such as lever springs. As a rule unalloyed steels are used for applications at room temperature whereas alloyed steels are generally used at a temperature above room temperature. Alloyed steels may also be chosen for above average tensile strengths.

 

A231 Alloy Spring Steel Wire Classification

The grade for normal applications made from unalloyed or alloyed steel has the abbreviation FD and is intended for static applications.

Spring steel wire for medium fatigue levels, such as required for some clutch springs from unailoyed or alloyed steel, has the abbreviation TD.

Spring steel wire from unalloyed steel or alloyed steel intended for use under severe dynamic duty such as for valve springs or other springs with similar requirements has the abbreviation VD.

Medium and high fatigue grades TD and VD are characterized by high steel cleanliness, specific chemical, mechanical and technological parameters and a well defined surface condition in relation to the allowable depth of surface defects and decarburization.

The static grade FD is characterized by its chemical, mechanical and technological characteristics as well as by a specified surface condition concerning surface defects and decarburization.

 

 

 

A231 Non metallic inclusions

The VD grades shall be checked for maximum size of inclusion according to ENV 10247. The allowable level of inclusions shall be agreed between the parties at the enquiry and order.

 

A231 Form of delivery

Alloy wire shall be supplied in coils, on spools or in cut lengths. The wire in coils or on spools shall form one continuous length. Wire in coil may also be supplied on carriers containing one or more coils.

 

For VD and TD grades no welds are permitted after the heat treatments preceding the final drawing operation; for 'FD' grades no welds shall be made at finished size unless agreed otherwise between the parties.

 

The supplied wire units shall be tightly bound to ensure that wire spiral waps do not spring out unforeseen. The starting end shall be marked and at the coil ends the wire shall be covered with a protective cap.

Information to be supplied by the purchaser

The purchaser shall clearly state in his enquiry or order the product and following information :

a)the desired quantity;

b)the number of this European Standard: EN 10270-2;

c)wire grade

d)the nominal wire diameter;

e)the form of delivery and unit mass;

f)the type of inspection document;

g)any particular agreement made.

KeyWords
Please send your message to us
*Email
Tel
*Title
*Content
Upload
  • Only supports .rar/.zip/.jpg/.png/.gif/.doc/.xls/.pdf, maximum 20MB.
CONTACT PERSON
Name:
Florence Tang
Tel:

86-731-89903933

Email:
Address:
ADD: No. 812-813, Floor 8, Building C2, Yongsheng Commercial Plaza, 222 Labor East Road, Yuhua District, Changsha City, Hunan, China.
NEWSLETTER

sign up for the latest catalogue, new design and promotion

follow us