To create value for customers, to be proud
of customers' continuous satisfaction
Home / All / Steel Forgings / Round Forgings /
AISI SAE 4340 30CrNiMo8 DIN 1.6580 Hot Forged Alloy Steel Round Bar
AISI SAE 4340 30CrNiMo8 DIN 1.6580 Hot Forged Alloy Steel Round Bar
| Categories | Round Forgings |
|---|---|
| Brand | fushun |
| Model | AISI SAE 4340 30CrNiMo8 DIN 1.6580 |
| Steel grade | AISI/SAE 4340 |
| Applications | Heavy Duty Shafts, Gears, Axles, Spindles, Couplin |
| Heat treatment | Normalized,Quenching and Tmenpering |
| Surface condition | Black or bright surface |
| Standard | ASTM A26 |
| Unit Price | US $ 1500 / metric ton |
| FOB port | SHANGHAI |
| Terms of Payment | L/C, D/A, D/P, T/T |
| Update Time | Apr 30,2025 |
Detail Information
Introduce
4340 steel is a nickel chromium molybdenum high hardenability high tensile steel, generally supplied hardened and tempered in the tensile range of 930 - 1080 Mpa (condition U) - (Rc 28 - 36). Characterised by high strength and toughness in relatively large sections. Pre hardened and tempered 4340 can be further surface hardened by flame or induction hardening and by nitriding. We also supply forged styeel bar, including 4130, 4140, 4145, 4145H, 4330V etc
Application
4340 is used in most industry sectors for applications requiring higher tensile/yield strength than 4140 can provide. Typical applications are: Heavy Duty Shafts, Gears, Axles, Spindles, Couplings, Pins etc
Quality Standard
EN 10277 Bright steel products. Technical delivery conditions. Steels for quenching and tempering
EN 10083 Steels for quenching and tempering. Technical delivery conditions for alloy steels
EN 10269 Steels and nickel alloys for fasteners with specified elevated and/or low temperature properties
EN 10263 Steel rod, bars and wire for cold heading and cold extrusion. Technical delivery conditions for steels for quenching and tempering
EN 10250 Open steel die forgings for general engineering purposes. Alloy special steels
ASTM A29 Standard Specification Steel Bars, Carbon and Alloy, Hot-Wrought, General Requirements
All Grades Comparison
Chemical Composition(%)
Mechanical Properties(T=20°C if not differently stated)
Heat treatment and hot plastic deformation temperatures
Heat Treatment
Annealing: Heat to 800 oC – 850 oC, hold until temperature is uniform throughout the section and cool in furnace.
Flame or Induction Hardening: 4340 steel can be further surface hardened by either the flame or induction hardening methods resulting in a case hardness in excess of Rc 50. Parts should be heated as quickly as possible to the austenitic temperature range (830 oC – 860 oC) and required case depth followed by an immediate oil or water quench, depending upon hardness required, workpiece size/shape and quenching arrangements. Following quenching to hand warm, most components should be tempered between 150 oC – 200 oC to remove quenching stresses in the case. This will have little effect on case hardness.
Hardening: Heat to 830 oC – 860 oC, hold until temperature is uniform throughout the section, soak for 10 – 15 minutes per 25 mm section, and quench in oil, water, or polymer as required.
Nitriding: 4340 steel can also be successfully nitrided, giving a surface hardness of up to Rc 60. Nitriding is carried out at 490 oC – 530 oC, followed by slow cooling (no quench) reducing the problem of distortion. Parts can therefore be machined to near final size, leaving a grinding allowance only. The tensile strength of the core is usually not affected since the nitriding temperature range is generally below the original tempering temperature employed. N.B. Nickel is inert to the action of nitrogen and in general resists its diffusion into steel. This can result in lower case hardness or longer nitriding cycle times for steels containing nickel such as 4340 steel.
Stress Relieving: Heat to 600 oC – 650 oC, hold until temperature is uniform throughout the section, soak for 1 hour per 25 mm of section, and cool in still air.
Tempering: Re-heat to 450 oC – 660 oC as required, hold until temperature is uniform throughout the section, soak for 1 hour per 25 mm of section, and cool in still air. N.B. Tempering should be avoided if possible within the range 250 oC – 450 oC due to temper brittleness.
Notes on Heat Treatment: Heating temperatures, rate of heating, cooling and soaking times will vary due to factors such as work piece size/shape also furnace type employed, quenching medium and work piece transfer facilities etc.
Machinability
4340 steel in the hardened and tempered as supplied condition is still regarded as being readily machinable and operations such as turning and drilling etc. it can be carried out satisfactorily using machine manufacturers, recommendations for suitable tool type – feeds and speeds.
Welding
Welding of 4340 steel in the hardened and tempered condition (as normally supplied), is not recommended and should be avoided if at all possible, as the mechanical properties will be altered within the weld heat affected zone. It is preferred that welding be carried out on 4340 steel while in the annealed condition, and that the work piece, immediately on cooling to hand warm, is then stress relieved at 640 oC – 660 oC prior to hardening and tempering.
If welding in the hardened and tempered condition is really necessary, then the work piece, immediately on cooling to hand warm, should be if possible stress relieved at 15 oC below the original tempering temperature (if known).
Mill′s test certificate
EN 10204/3.1 with all relevant data reg. chem. composition, mech. properties and results of testing.
Related Products
Please send your message to us
- Tel
- *Title
- *Content
CONTACT PERSON
- Name:
- Florence Tang
- Tel:
86-731-89903933
- Address:
- ADD: No. 812-813, Floor 8, Building C2, Yongsheng Commercial Plaza, 222 Labor East Road, Yuhua District, Changsha City, Hunan, China.
COMPANY
NEWSLETTER
sign up for the latest catalogue, new design and promotion
follow us
Mobile WEB
